Setting up iSCSI over IPv6 on Proxmox 8 isn’t covered in the official docs, which only deal with IPv4. Here’s the step-by-step with TrueNAS as the target, including the Proxmox 8-specific initiator settings.

TrueNAS side: configure the target for IPv6
First, make sure TrueNAS has an IPv6 address on the interface you’ll use for iSCSI. In TrueNAS, go to Network > Interfaces, edit the interface, and add an IPv6 address. It can be a static address or SLAAC, but it needs to be reachable from Proxmox.
Next, create the iSCSI target. In TrueNAS, go to Sharing > Block Shares (iSCSI). Click Add. In the Target section, set the target name (e.g., iqn.2005-10.org.freenas.ctl:proxmox8). Under Portal, add a portal with the IP address set to :: (all IPv6 addresses) or a specific IPv6 address. Port 3260 is standard.
Create an extent (the storage backing the target) and associate it with the target. Make sure the initiator group allows your Proxmox host’s initiator name. You can set the initiator name to allow all (ALL) for testing, but better to restrict it later.
Proxmox 8 initiator settings
On Proxmox, install open-iscsi if it’s not already there:
apt install open-iscsi
Edit /etc/iscsi/iscsid.conf and set the initiator name to match what you allowed in TrueNAS:
InitiatorName=iqn.1993-08.org.debian:01:proxmox8node
Now, the key part for IPv6: Proxmox 8 uses the iscsid daemon, and by default it may not listen on IPv6. Check /etc/iscsi/iscsid.conf for this line:
node.startup = automatic
Also, ensure that the iSCSI service is enabled and started:
systemctl enable --now iscsid open-iscsi
Then discover the target using the IPv6 address. The syntax is a bit different; you need to enclose the IPv6 address in brackets and specify the port:
iscsiadm -m discovery -t st -p [2001:db8::1]:3260
If discovery works, you’ll see the target listed. Now log in:
iscsiadm -m node -T iqn.2005-10.org.freenas.ctl:proxmox8 -p [2001:db8::1]:3260 --login
Check that the session is up:
iscsiadm -m session
You should see the connection with the IPv6 address. If it fails, check /var/log/syslog for iscsid errors. One common issue: the Proxmox firewall might block IPv6 traffic on port 3260. Make sure to allow it in the datacenter firewall settings for the host.

Add the iSCSI LUN as storage in Proxmox
Once logged in, the new disk appears as /dev/sdX (or /dev/sdXX for multipath). In Proxmox, go to Datacenter > Storage > Add > iSCSI. Enter the ID, portal (the IPv6 address in brackets, port 3260), and select the target. Proxmox will then create the storage and you can use it for VM disks.
If you want multipath, install multipath-tools and configure /etc/multipath.conf. But for a simple setup, direct disk is fine.
Verification
To confirm IPv6 is actually being used, run:
ss -tnp | grep 3260
You should see a connection with the IPv6 address, not IPv4. Also check the iSCSI session details:
iscsiadm -m session -P 3
Look for the transport line showing tcp and the IPv6 address.
That’s it. The official docs skip IPv6 entirely, but with these settings it works. Just remember to allow port 3260 in the firewall and use brackets around the IPv6 address in all iscsiadm commands.
Related: Proxmox iSCSI Multipath: Setup with TrueNAS and Failover Test